How to make the Webster Dress more fitted

June 21, 2017   /   byJenny Rushmore  / Categories :  Feeds

Howdy sewing friends! So as you’ve seen by now, our latest pattern, the Webster Top and Dress is designed to be an airy, floaty, swooshy garment – perfect for hot summer days. It’s fitted through the shoulders and bust, and then flares out pretty dramatically for a silhouette that’s almost trapeze-like. It’s not necessarily going to make you look thinner, but in our books, that’s not always the point of our clothes!

But what if you love the look of the Webster but want a more fitted look? Don’t despair: there are actually quite a few approaches, and I’m going to take you through three of them today. One thing to note: because there are no closures (zips, buttons or the like) you don’t want to make your Webster TOO fitted, or you’re not going to be able to get it on and off. However there are definitely ways to make it a little more form fitting and a little less voluminous.

Cashmerette Webster Top & Dress

The original Webster Dress in its swingy glory!

1. Grade between sizes

If you want to retain exactly the same look on your Webster, but with a closer fit, then grading between sizes is the easiest approach. Start by picking the right size for your bust. Then, decide how many sizes you want to go down for the rest of the garment. The way to do that is to look at the Finished Garment Measurements, which show you how large the actual dress is. You definitely still need to have quite a lot of ease to be able to get it on and off, but in most cases, you’d be safe going down 1 – 2 sizes.

So let’s say you are a perfect fit for the body measurements of the 18 G/H (48″ – 38″ – 48″). If  you graded down to the 14 waist and hip, the garment would still be 51″ at the waist and 55″ at the hip – enough to get over your size 18 bust, but overall you’ll have 4 inches less of ease than if you made a straight 18.  If you’re normally a bigger size at the waist/ hip (e.g. if you’re an 18 G/H bust, but a 22 waist/hip), conversely you could just make a straight 18.

To grade between sizes, start by marking your bust size on the side seam, at the bottom of the bust dart (indicated by a red circle here). Then, mark the size you want to grade down to around the waist. Note that there is no defined waist point on the Webster (it doesn’t go in!) so it’s really up to you where you want to put that. Then, join up the bust and waist points with a smooth line. Continue down the line of the smaller size, and onto the bottom hem band. Then cut your fabric and sew as normal!


2. Add waist ties

A second approach is to add waist ties that will cinch the dress in at the waist. This is a very simple method, and you can make the ties as short or long as you like, and either tie them at the front, the back, or even make them super long and wrap them around you all the way.

First, decide how long you want your ties to be (I usually drape a measuring tape around me or a scrap of fabric to assess). Construct them using the same method as for the Webster back straps.

Once you’ve attached the facing but the dress is still flat, baste the straps onto the back side seams at whatever height you like. Then, complete construction as normal.



3. Add a waist drawstring or elastic

This final approach is inspired by the True Bias Southport dress! You’ll add a channel to the outside of the dress, and then you can either insert a drawstring or a piece of elastic (there’s a slight difference in construction for elastic).

First up, create the channel.

To calculate how long your channel piece should be, first measure the width of your pattern pieces at the height where you want the channel, allowing for a 1.5″ gap at the center front (and a 1/2″ seam allowance at each end). So for instance, if your pattern pieces are 40″ around, then your piece would be 40″ – 1.5″ + 0.5″ + 0.5″ = 39.5″ long. For a 1 inch wide finished channel, the depth of the piece should be 2″. So: cut a rectangle of your fabric that’s your desired length by 2″ deep.

Once you have that piece, fold over each long side to the wrong side by 1/2″ and press (note the illustrations are not to scale). Then, fold over each short end to the wrong side by 1/2″ and press again. Now, from the right side, topstitch down each long end.


Create the drawstring as long as you’d like, using the same method as the Webster back straps.

Once you’ve completed constructing your dress, pin the channeling on to the dress at the desired height, and topstitch it to the dress at the top and bottom (make sure you’re accurate and leaving enough of a gap in the middle!). Pin a safety pin through the drawstring, and insert into the channel and you’re done!

To insert elastic, follow the same approach for the channel, but without the 1.5″ gap in the center. Sew the channel in a loop, then pin to the dress. Topstitch the channel to the dress, leaving a 2 inch gap in the bottom topstitching. Wrap a piece of 1/4″ elastic around your waist and stretch until it is snug but comfortable. Cut. Pin a safety pin through the elastic, and feed through the channeling. Sew the two ends of the elastic together, and then topstitch the 2 inch gap closed.

So there are three approaches to making your Webster Dress more fitted! What do you think: will you be trying any of them?

The post How to make the Webster Dress more fitted appeared first on Cashmerette.

This is a syndicated post. Please visit the original author at Cashmerette

You may like

And lo, such a thing exists

As much as I thought it might not, time is starting to assume its normal course.  The days are starting to be the length that I expect them to be, not stretching out in front of me like a desert … Continue reading

read more

Estate Sale Shopping Online

Estate sales are one of my FAVORITE things. I am lucky enough to live in an area with…

read more

Technique for Joining Standing Legs in Amigurumi without a Hole

Today we’re lucky enough to have a guest post written by Mirena of Mirena Made! Mirena has been a FreshStitches customer for years, and she creates hand-crocheted creations that she sells in her shop. (yes, you too can sell finished FreshStitches animals!) Thank you so much, Mirena, for coming by and sharing this new technique […]

read more

Miss Fisher’s riding suit jacket knock-off: the slanted flap pockets – bolsos inclinados com paleta

EN Summary: These pockets aren’t easy to sew without hazards and I thought my readers would appreciate photos of the sewing process, along with my notes (to fully understand the process it’s also useful to have the pattern instructions at hand). Keep reading the full article.
PT Sumário: Este género de bolsos não são nada fáceis de costurar bem e achei que os meus leitores iriam apreciar fotos detalhando o processo, acompanhadas pelas minhas notas (não dispensa a consulta das instruções que vêm incluídas no molde). Continuem a ler o artigo completo.

Read more – Continuar a ler »

Couture et Tricot is licensed with a Creative Commons Attribution-NonCommercial-NoDerivs license
read more