Madalynne X Simplicity 8435 Bodysuit Placket Tutorial

July 10, 2017   /   byMaddie Flanigan  / Categories :  Feeds

diy bodysuitI’ve said it before and I’ll say it again, I’m a visual learner. Give me directions and in an hour, I’ll be pulling my hair out trying to follow. I need pictures or a video to fully understand any kind of process. For this reason, I’m creating several tutorials for my new patterns with Simplicity (psssttt… did you see the FULL video tutorial for the 8437?). Below, I show how to sew the center front placket for the 8435 bodysuit. You can purchase the kit here and the pattern here. It’s not hard to sew, just a lot of steps that have to be precise so that your placket isn’t wonky.

There is nothing more fulfilling to me than seeing what you make. So if this tutorial gets your sewing mojo going and you’re pumped to make a bodysuit, hop on over to the shop to purchase a kit and pattern, and then share with me via email or on Instagram (tag @mmadalynne and use #bramakingwithmadalynne). Stay tuned later this week to this the bodysuit all sewn up! Sneak peek here.

PREP
Before getting to the actual sewing, let’s look at where you should be at this point in the project. You should have sewn the front and the back together at the shoulder seams, marked the placket placement (I used a regular pen since it will be hidden once placket is sewn), cut down the center front according to pattern markings, and added binding to neck. This is not in the pattern directions, but I also added a square of fusible interfacing on the interior/wrong side at the bottom (where the triangle is) to reinforce. Last, you could have both plackets cut out. I added fusible interfacing to reinforce.
bodysuit patternbodysuit pattern bodysuit pattern bodysuit pattern bodysuit pattern bodysuit patternSTEP ONE:

  • Overlock one long edge on each placket.
  • On edge that was not overlooked, fold and press ½” from edge.
  • With right sides facing, place placket on bodysuit, right sides together. Fold line on placket and front should align and placket should extend above neckline approximately ¼” and below triangle at bottom approximately ¼”.
  • Pin in place, then sew down fold line with a straight stitch. Back stitch and top and bottom, and approximately ½” above bottom of placket, use a shorter stitch length (1.5mm).

bodysuit pattern bodysuit pattern bodysuit pattern bodysuit pattern bodysuit pattern bodysuit pattern bodysuit patternbodysuit pattern bodysuit patternSTEP TWO:

  • At neckline, fold placket back on itself so right sides are facing. Serged edge should align with seam line.
  • Sew across top edge with ¼” seam allowance. For seams that are short in length, I find it easier to start sewing in the center, sew to the end, flip around, and then sew to the beginning.
  • Use thumb and index finger to turn placket right side out. Getting your thumb as close as possible to the corner really helps to create a sharp point when it’s flipped.
  • Repeat previous 3 points to attach other placket. Use pins or spray adhesive to hold in place temporarily.
  • Lightly press. Use steam if needed (sometimes the tip gets slightly stretch out from sewing, so it’s pointy. Steaming it helps, but only if you allow is to cool before moving. The cooling portion sets it into shape).

bodysuit pattern bodysuit pattern bodysuit patternbodysuit pattern bodysuit pattern bodysuit patternSTEP THREE:

  • At the bottom, fold plackets back to reveal a small triangle. With small triangle facing up and wearer’s right placket on top of wearer’s left, sew across using a straight stitch. Stitching should only go through small triangle and plackets (not bodysuit).

bodysuit patternSTEP FOUR:

  • Edgestitch inner edge of plackets from neckline to as close to bottom as you can get. For seams that are bulky at the beginning, like the top of this placket, it’s hard to start sewing. Since this stitching will be visible on the exterior of the garment, you want to make sure it’s as neat as possibly. Top stitching will NEVER be 100%, but to get it as neat as possible, I start sewing wherever the bulkiness ends, which in this case is about 3/4-1″ below top edge all the way to the bottom. I don’t back stitch at the top (where I started sewing), but I DO back stitch at the end. Then I go back up to where I started stitching, and stitch from there to the beginning of the seam (top edge of placket). Overlapping the stitches does the same thing as back stitching (locks the seam in place). Just be sure to overlap as precisely as possible so it does lock the stitches.
  • Use pattern piece to pin mark where the box is sewn. Using a straight stitch and starting from inner edge of wearer’s right placket, sew across, down, and then across again. See photo for reference of where to start stitching. Then sew the ‘X’ in the middle.

bodysuit pattern bodysuit pattern bodysuit patternSTEP FIVE:

  • Add snaps using the directions on the snap attacher. I have found that it is easier to attach the female snaps with the attacher (just using a hammer), but for the male snaps, you’ll definitely need the attacher tool.
  • Continue sewing bodysuit per pattern directions

bodysuit pattern

The post Madalynne X Simplicity 8435 Bodysuit Placket Tutorial appeared first on Madalynne.

This is a syndicated post. Please visit the original author at Madalynne

You may like


Simplicity 8105

A quick post about a quick tee I made for Liddy.The Simplicity 8105 I saw this pattern on Lara’s instagram and thought it was perfect for my girls too.I sewed up the largest size (a 14 I think) in a stretchy cott…

read more

#ebonyTee – just two more (for now)

Yes, I know! MORE Ebony Tee’s…haven’t I got anything better to do? Well yes (actually no – so if you have any pattern suggestions please let me know)…but these are different as I’ve added one inch to the length so I can wear them with my tighter pa…

read more

The Buying a House Blouse


Hello, everyone!  It’s been quite a while since I have posted anything.



The main reason for my online disappearance is the fact that I am now a homeowner!  That process has kept me rather busy, and the move, etc., has not left much time for sewing, let alone blogging.  I was actually without internet for a couple of weeks which was rather refreshing.


Of course, I wanted to make a new outfit for the occasion, but there was not a lot of free time prior to closing.  But I was determined!  


I have been wanting to make this blouse for years.  I often pull out scraps of fabric along with the pattern, hoping that I can squeeze out an entire garment, but it never has worked for me.  Until now!


The leftovers from this skirt and this dress were tucked away in a drawer, and while the dye lots do not match, I think I managed to make it work.  The neck tie was made with the leftovers from the skirt, and the rest of the blouse (which is a slightly more pigmented and heavier weight cotton) was cut from the remains of the dress.  There were quite a few people who thought that the look was actually a dress, so I guess the difference is not terribly obvious.


These photos were taken about an hour after signing all of the paperwork (in my old neighborhood).  I was exhausted, but very happy.


I really began looking in earnest over a year ago, so it was a huge relief to finally be done.


It has been quite an adventure, and my new living space is still not “finished,” but Valentino and I are definitely settling in, and I am finally getting back into a routine – one that will definitely include many more sewing adventures!



Blouse:  Made by me, Butterick 4985

Skirt:  Made by me, Butterick 4792
Shoes:  Born “Kharen”

read more

What to Pack For a Day at the Beach With a Toddler

It’s not summer to me until we’ve been to the beach. Being by the water has always been so restful and healing for my soul. The older I get, the more of a beach gal I seem to become. I’m happy to report that Piper shares my love of the water and has loved the […]

The post What to Pack For a Day at the Beach With a Toddler appeared first on Love Lola | A Life & Style Blog.

read more

0 comments

Leave a reply

Jan 2016 Accuquilt Sale